Physical Element Creation Reference Table

Branch Creation in Physical

The extremity status of the logical wire will decide the branch end behavior in physical. The table below identifies all the possibilities of branch ending at the physical equipment.

If the logical pathway segment is ending on the equipment pathway end (PCP on fly), there are following possibilities of branch ending at the physical equipment:


Logical Pathway Ending Pattern	Connection status between Logical Connector and Logical Equipment Connector Port	Logical Wire Route status	Logical Wire ending status	Effect on Branch Creation in Physical
Logical Pathway Ending Pattern		Logical Wire Route status	Logical Wire ending status	Generate Branches to Cavity - OFF	Generate Branches to Cavity - ON
Logical Pathway Segment ending on Equipment Pathway end (PCP on fly)	At least one logical equipment connector port is connected to logical connector component	Logical wire is routed till	Pin on Logical Equipment	At least 3 branches will be created Branch1 will end in barycenter Branch2 between the barycenter and cavity (with the same name as Pin) on Physical Equipment corresponding to the Logical Equipment If the cavity having the same name as logical pin is not found Branch2 will not be created	At least 2 branches will be created Branch1 will end in barycenter Branch2 between the barycenter and cavity (with the same name as Pin) on Physical Equipment corresponding to the Logical Equipment If the cavity having the same name as logical pin is not found Branch2 will not be created
			Pin on Logical Equipment Connector Port	At least 2 branches will be created Branch1 will end in barycenter Branch2 between the barycenter and the first compatible connection point on Physical Equipment connector (if found) corresponding to the Logical Connector port OR Branch2 between barycenter and cavity (with the same name as Connector Port, if the predefined part number of Connector Port is unset) on Physical Equipment corresponding to the Logical Equipment. If cavity having the same name as logical pin is not found, branch2 will not be created	At least 2 branches will be created Branch1 will end in barycenter Branch2 between the barycenter and cavity (with the same name as Pin) on Physical Equipment connector corresponding to the Logical Equipment connector port If cavity having the same name as logical pin is not found, branch2 will not be created
			Pin on Logical Connector Component	At least 2 branches will be created Branch1 will end in barycenter Branch2 between the barycenter and first compatible connection point on Physical Harness Connector corresponding to the Logical Connector Component	At least 2 branches will be created Branch1 will end in barycenter Branch2 between the barycenter and cavity (with the same name as Pin) on Physical Harness connector corresponding to the Logical connector component If the cavity having the same name as logical pin is not found branch2 will not be created
		Logical wire is not routed		At least 2 branches will be created Branch1 will end in barycenter Branch2 between the barycenter and the first compatible connection point on the Physical harness connector corresponding to Logical Connector Component connected to the Logical Equipment Connector Port	Only one branch (Branch1) will be created and will end in barycenter
	No logical Equipment Connector Port is connected to Logical Connector Component	Logical wire is routed till	Pin on Logical Equipment	At least 2 branches will be created Branch1 will end in barycenter Branch2 between the barycenter and cavity (with the same name as Pin) on Physical Equipment corresponding to the Logical Equipment If the cavity having the same name as logical pin is not found, Branch2 will not be created	At least 2 branches will be created Branch1 will end in barycenter Branch2 between the barycenter and cavity (with the same name as Pin) on Physical Equipment corresponding to the Logical Equipment If the cavity having the same name as logical pin is not found, Branch2 will not be created
			Pin on Logical Equipment Connector Port	At least 2 branches will be created Branch1 will end in barycenter Branch2 between the barycenter and the first compatible connection point on Physical Equipment connector (if found) corresponding to the Logical Connector port OR Branch2 between barycenter and cavity (with the same name as Connector Port, if the predefined part number of Connector Port is unset) on Physical Equipment corresponding to the Logical Equipment. If the cavity having the same name as logical pin is not found Branch2 will not be created	At least 2 branches will be created Branch1 will end in barycenter Branch2 between the barycenter and cavity (with same name as Pin) on Physical Equipment connector corresponding to the Logical Equipment Connector Port If the cavity having the same name as the logical pin is not found, Branch2 will not be created
			Pin on Logical Connector Component	Only one branch Branch1 will be created and will end in barycenter	At least 2 branches will be created Branch1 will end in barycenter Branch2 between the barycenter and cavity (with the same name as Pin) on Physical Harness Connector corresponding to the Logical connector component If the cavity having the same name as logical pin is not found, Branch2 will not be created
		Logical wire is not routed	At least 2 branches will be created Branch1 will end in barycenter Branch2 between the barycenter and the first compatible connection point on Physical Equipment Connector corresponding to Logical Connector port	Only one branch (Branch1) will be created and will end in barycenter

Important: If two or more logical pathway segments are connected to the logical equipment through pathway end (PCP on the fly), only the pathways, which are required to generate complete physical electrical network (based on routed elements and connector at the other end), will be synchronized.

If the logical pathway segment is ending on the equipment on PCP, there are following possibilities of branch ending at the physical equipment:


Logical Pathway Ending Pattern	Is PCP connected to a Connector Port	Connection status between Logical Connector and Logical Equipment Connector Port	Logical Wire Route status	Logical Wire ending status	Effect on Branch Creation in Physical
Logical Pathway Ending Pattern	Is PCP connected to a Connector Port		Logical Wire Route status	Logical Wire ending status	Generate Branches to Cavity - OFF	Generate Branches to Cavity - ON
Logical Pathway Segment ending on Equipment on PCP	PCP is connected to at least one connector port	At least one logical equipment connector port is connected to logical connector component	Logical wire is routed till	Pin on Logical Equipment	At least 3 branches will be created Branch 1 will end in barycenter Branch2 between the barycenter and cavity (with the same name as Pin) on Physical Equipment corresponding to the Logical Equipment pin If the cavity having the same name as logical pin is not found, branch2 will not be created Branch 3 between the barycenter and the first compatible connection point on Physical Harness Connector corresponding to the Logical Connector Component connected to the logical equipment connector port associated to PCP	At least 1 branches will be created Branch1 will end in barycenter Branch2 between the barycenter and cavity (with the same name as Pin) on the Physical Equipment corresponding to the Logical Equipment pin If the cavity having the same name as logical pin is not found, branch2 will not be created
				Pin on Logical Equipment Connector Port	At least 2 branches will be created Branch1 will end in barycenter Branch 2 between the barycenter and the first compatible connection point on Physical Equipment Connector corresponding to the Logical Connector Port (Cwire) on which wire ends if Logical Equipment connector port (Cpcp) associated with PCP is different than the connector port on which the logical wire ends (Cwire), Branch3 will be created between the barycenter point and the first compatible connection point on physical corresponding to Cpcp	At least 1 branch will be created Branch 1 will end in barycenter Branch2 between barycenter and cavity (with same name as Pin) on Physical connector corresponding to Logical Equipment connector port(Cwire) If the cavity having the same name as logical pin is not found, Branch2 will not be created if Logical Equipment connector port (Cpcp) associated with PCP is different than the connector port on which logical wire ends (Cwire), Branch 3 will be created between barycenter point and First compatible connection point on physical corresponding to Cpcp
				Pin on Logical Connector Component	At least 2 branches will be created Branch1 will end in barycenter Branch 2 between BaryCenter and First compatible connection point on Physical Harness Connector corresponding to logical connector component connected to logical equipment connector port (Cwire) on which wire ends if Logical Equipment connector port (Cpcp) associated with PCP is different than the connector port on which logical wire ends (Cwire), Branch 3 will be created between barycenter point and First compatible connection point on physical corresponding to Cpcp	At least 1 branch will be created Branch 1 will end in barycenter Branch2 between barycenter and cavity (with same name as Pin) on Physical Harness Connector corresponding to logical connector component connected to logical equipment connector port (Cwire) on which wire ends If the cavity having the same name as logical pin is not found, Branch2 will not be created if the Logical Equipment Connector Port (Cpcp) associated with PCP is different than the connector port on which the logical wire ends (Cwire), Branch3 will be created between the barycenter point and the first compatible connection point on physical corresponding to Cpcp
			Logical wire is not routed		At least 2 branches will be created Branch1 will end in barycenter Branch 2 will be created between barycenter point and First compatible connection point on physical corresponding to Cpcp	Only one branch Branch1 will be created and will end in barycenter
		No logical equipment connector port is connected to logical connector component	Logical wire is routed till	Pin on Logical Equipment	At least 2 branches will be created Branch1 will end in barycenter Branch2 between the barycenter and cavity (with the same name as Pin) on Physical Equipment corresponding to the Logical Equipment pin If the cavity having the same name as logical pin is not found, branch2 will not be created if the Logical Equipment connector port (Cpcp) associated with PCP is different than the connector port on which the logical wire ends (Cwire), Branch3 will be created between the barycenter point and the first compatible connection point on physical corresponding to Cpcp	At least 1 Branch will be created Branch1 will end in barycenter Branch2 between the barycenter and cavity (with the same name as Pin) on Physical Equipment corresponding to the Logical Equipment pin If the cavity having the same name as logical pin is not found, Branch2 will not be created
				Pin on Logical Equipment Connector Port	At least 2 branches will be created Branch1 will end in barycenter Branch2 between the barycenter and the first compatible connection point on Physical Equipment Connector corresponding to the logical connector port (Cwire) on which wire ends if the Logical Equipment connector port (Cpcp) associated with PCP is different than the connector port on which the logical wire ends (Cwire), Branch3 will be created between the barycenter point and the first compatible connection point on physical corresponding to Cpcp	At least 1 branch will be created Branch1 will end in barycenter Branch2 between barycenter and cavity (with same name as Pin) on Physical Equipment Connector corresponding to logical equipment connector port (Cwire) on which the wire ends If the cavity having the same name as logical pin is not found, Branch2 will not be created
				Pin on Logical Connector Component	At least 1 branch will be created Branch1 will end in barycenter Branch2 will be created between the barycenter point and the first compatible connection point on physical corresponding to Cpcp	Only one branch (Branch1) will be created which will end in barycenter
			Logical wire is not routed		At least 1 branch will be created Branch1 will end in barycenter Branch2 will be created between the barycenter point and the first compatible connection point on physical corresponding to Cpcp	Only one branch (Branch1) will be created and will end in barycenter
	PCP is not connected to any connector port	At least one logical Equipment Connector Port is connected to Logical Connector Component	Logical wire is routed till	Pin on Logical Equipment	At least 1 branch will be created Branch1 will end in barycenter Branch2 between the barycenter and cavity (with the same name as Pin) on Physical Equipment corresponding to the Logical Equipment pin If the cavity having the same name as logical pin is not found, branch2 will not be created	At least 1 Branch will be created Branch1 will end in barycenter Branch2 between the barycenter and cavity (with the same name as Pin) on Physical Equipment corresponding to the Logical Equipment pin If the cavity having the same name as logical pin is not found, branch2 will not be created
				Pin on Logical Equipment Connector Port	A tleast 1 Branch will be created Branch1 will end in barycenter Branch2 between the barycenter and the first compatible connection point on Physical Equipment Connector corresponding to the logical connector port (Cwire) on which the wire ends	At least 1 branch will be created Branch1 will end in barycenter Branch2 between barycenter and cavity (with same name as Pin) on Physical connector corresponding to Logical Equipment connector port (Cwire) If the cavity having the same name as logical pin is not found, Branch2 will not be created
				Pin on Logical Connector Component	At least 1 branch will be created Branch1 will end in barycenter Branch 2 between BaryCenter and First compatible connection point on Physical Harness Connector corresponding to logical connector component connected to logical equipment connector port (Cwire) on which wire ends	At least 1 branch will be created Branch1 will end in barycenter Branch2 between the barycenter and cavity (with the same name as Pin) on Physical Harness Connector corresponding to the logical connector component connected to logical equipment connector port (Cwire) on which the wire ends If the cavity having the same name as logical pin is not found, Branch2 will not be created
			Logical wire is not routed		Only one branch (Branch1) will be created and will end in barycenter	Only one branch (Branch1) will be created and will end in barycenter
		No logical Equipment Connector Port is connected to logical connector component	Logical wire is routed till	Pin on Logical Equipment	At least 1 branch will be created Branch1 will end in barycenter Branch2 between the barycenter and cavity (with the same name as Pin) on Physical Equipment corresponding to the Logical Equipment Pin If the cavity having the same name as logical pin is not found, branch2 will not be created	At least 1 branch will be created Branch1 will end in barycenter Branch2 between the barycenter and cavity (with the same name as Pin) on Physical Equipment corresponding to the Logical Equipment pin If the cavity having the same name as logical pin is not found, branch2 will not be created
				Pin on Logical Equipment Connector Port	At least 1 branch will be created Branch1 will end in barycenter Branch2 between the barycenter and the first compatible connection point on Physical Equipment Connector corresponding to the Logical Connector Port (Cwire) on which the wire ends	At least 1 branch will be created Branch1 will end in barycenter Branch2 between barycenter and cavity (with same name as Pin) on Physical Equipment Connector corresponding to logical equipment connector port (Cwire) on which the wire ends If the cavity having the same name as logical pin is not found, Branch2 will not be created
				Pin on Logical Connector Component	Only one branch (Branch1) will be created and will end in barycenter	Only one branch (Branch1) will be created and will end in barycenter
			Logical wire is not routed		Only one branch (Branch1) will be created and will end in barycenter	Only one branch (Branch1) will be created and will end in barycenter

Important: The branch creation in physical may vary as per the logical wire ending status.

Equipment Creation

With the Logical To Physical command, the harness connector can be directly connected to the physical equipment (corresponding to the logical equipment) through the cavity (having the same name as the logical connector port) according to the criteria below:

The pre-defined part number of the connector port (of the logical Equipment) should be unset.
The harness connector should be linked with the connector port of the logical equipment.

Busbar Creation

With the Logical To Physical command, a logical busbar is migrated as a physical equipment. Generation and synchronization behaviors for logical busbars are the same as for logical equipments.

However, the migration behavior of logical terminal ports on busbars is specific. Logical terminal ports (through which a bus bar inducts and gets its power source) are migrated as physical equipment connectors. After the migration of a busbar with a terminal port, the instantiated physical equipment and physical equipment connector are connected through:

A cavity, which is present on the physical equipment
Note: The cavity has the same name as the logical terminal port.
A cavity connection point, which is present on the physical equipment connector

Harness Connector Modification

With the Logical To Physical command, physical data is modified when:

The pre-defined part number of the logical harness connector is modified in the logical and / or corresponding physical connector has a different part number.
No pre-defined part number set on the logical connector port linked to the logical harness connector, the physical harness connector is connected directly to the cavity of physical equipment.

Connector Port Modification

With the Logical To Physical command,

If the pre-defined part number of the logical connector port is unset (connector port connected to the harness connector), the corresponding equipment connector (if it exists) is removed in the physical, and the physical harness connector is instantiated and directly connected to the cavity of the physical equipment.
If the pre-defined part number of the logical connector port is set (connector port connected to the harness connector), the corresponding physical equipment connector will be instantiated and connected to the cavity of the physical equipment. The physical harness connector (if any corresponding to logical harness connector) is connected to the physical equipment connector.