Display

Default graphic properties

Construction Geometry

Apply Graphic Properties

Defines whether all graphic properties for constructed geometry are applied.

By default, this check box is cleared.

Fill

Color: Defines the color for constructed geometry.; the black color is selected.
Transparency: Defines the transparency for constructed geometry.; the value is 128.

Edges

Color: Defines the color of edges for constructed geometry.; the black color is selected.
Linetype: Defines the linetype of edges for constructed geometry.; the linetype is 4 (Dot-Dashed).
Thickness: Defines the thickness of edges for constructed geometry.; the thickness is 1 (very thin line).

Lines and Curves: Color

Defines the color of lines and curves for constructed geometry.

the black color is selected.

Linetype

Defines the line type of lines and curves for constructed geometry.

the linetype is 4 (Dot-Dashed).

Thickness

Defines the thickness of lines and curves for constructed geometry. By default, the thickness is 1 (very thin line).

the thickness is 1 (very thin line).

Points

Color: Defines the color of points for constructed geometry.; the black color is selected.
Symbol: Defines the symbol of points for constructed geometry.; the symbol is a cross.

Restricted Area

Apply Graphic Properties

Defines whether all graphic properties for the restricted area are applied.

By default, this check box is cleared.

Fill

Color: Defines the color for the restricted area.; the black color is selected.
Transparency: Defines the transparency for the restricted area.; the value is 128.

Edges

Color: Defines the color of edges for the restricted area.; the black color is selected.
Linetype: Defines the line type of edges for the restricted area.; the linetype is 4 (Dot-Dashed).
Thickness: Defines the thickness of edges for the restricted area.; the thickness is 2 (0.35mm).

Lines and Curves

Color: Defines the color of lines and curves for the restricted area.; the black color is selected.
Linetype: Defines the line type of lines and curves for the restricted area.; the linetype is 4 (Dot-Dashed).
Thickness: Defines the thickness of lines and curves for the restricted area.; the thickness is 2 (0.35mm).

Points

Color: Defines the color of points for the restricted area.; the black color is selected.
Symbol: Defines the symbol of points for the restricted area.; the symbol is a cross.

Datum Target

Apply Graphic Properties

Defines whether all graphic properties for datum target geometries are applied.

By default, this check box is cleared.

Fill

Color: Defines the color for the datum target geometries.; the black color is selected.
Transparency: Defines the transparency for the datum target geometries.; the value is 128.

Edges

Color: Defines the color of edges for the datum target geometries.; the black color is selected.
Linetype: Defines the line type of edges for the datum target geometries.; the linetype is 5 (Phantom).
Thickness: Defines the thickness of edges for the datum target geometries.; the thickness is 1 (very thin line).

Lines and Curves

Color: Defines the color of lines and curves for the datum target geometries.; the black color is selected.
Linetype: Defines the line-type of lines and curves for the datum target geometries.; the linetype is 5 (Phantom).
Thickness: Defines the thickness of lines and curves for the datum target geometries.; the thickness is 1 (very thin line).

Points

Color: Defines the color of points for the datum target geometries.; the black color is selected.
Symbol: Defines the symbol of points for the datum target geometries.; the symbol is a cross.

Contacting Feature

Apply Graphic Properties

Defines whether all graphic properties for contacting feature are applied.

By default, this check box is cleared.

Fill

Color: Defines the color for the contacting feature.; the symbol is a cross.
Transparency: Defines the transparency for the contacting feature.; the value is 128.

Edges

Color: Defines the color of edges for the contacting feature.; the black color is selected.
Linetype: Defines the linetype of edges for the contacting feature.; the linetype is 5 (Phantom).
Thickness: Defines the thickness of edges for the contacting feature.; the thickness is 1 (very thin line).

Lines and Curves

Color: Defines the color of lines and curves for the contacting feature.; the black color is selected.
Linetype: Defines the linetype of lines and curves for the contacting feature.; the linetype is 5 (Phantom).
Thickness: Defines the thickness of lines and curves for the contacting feature.; the thickness is 1 (very thin line).

Points

Color: Defines the color of points for the contacting feature.; the black color is selected.
Symbol: Defines the symbol of points for the contacting feature.; the symbol is a cross.

Grid

Display

Defines whether the grid is displayed.

By default, this check box is cleared.

Allow Distortions

Defines whether grid spacing and graduations are the same horizontally and vertically.

By default, this check box is cleared.

H Primary spacing

Defines the grid horizontal spacing.

By default, the value is:

1 mm for Small range
100 mm for Normal range
1e+004 mm for Large range

H Graduations

Defines the grid horizontal graduations.

By default, the number of graduation is 10 for any range.

V Primary spacing

Defines the grid vertical spacing.

Important:

Only applicable when Allow Distortions is selected.

By default, the value is:

1 mm for Small range
100 mm for Normal range
1e+004 mm for Large range

V Graduations

Defines the grid vertical graduations.

Important:

Only applicable when Allow Distortions is selected.

By default, the number of graduation is 10 for any range.

Non-Semantic

Mark non-semantic annotations

Defines whether non-semantic annotations (datum elements, datum targets, geometrical tolerances, linear, and angular dimensions) are marked with a wavy red line in the tree and in the geometry.

By default, this check box is cleared.

Switch off text, Flag Note, NOA marking: Defines whether text, flag notes, and NOA markings are marked as non-semantic annotations. When selected, the text, flag notes, and NOA markings are not marked with a wavy red line. You can select the Switch off text, Flag Note, NOA marking check box when the Mark non-semantic annotations check box is selected.
By default, this check box is cleared.

Tree

Track history of displayed views and captures

Defines whether browsing history of views and captures is displayed in the tree. When selected, each browsed view or capture remains identified using a purple background in the Specification Tree.

Important:

If you clear this check box, it does not reset the current history of views and captures.

By default, this check box is selected.

Under Geometric Feature nodes

Defines that 3D annotations should be displayed under the geometric feature nodes in the specification tree. This lets you view 3D annotations under the Part Design or Generative Shape Design feature nodes to which they are applied.

By default, this check box is cleared.

Under View/Annotation Plane nodes

Defines that 3D annotations should be displayed under the view/annotation plane nodes in the specification tree. This lets you view 3D annotations under the view node to which they are linked.

By default, this check box is cleared.

Under Annotations Set node

Defines that 3D annotations should be displayed under the annotation set node in the specification tree.

Important:

Only applicable when Under View/Annotation Plane nodes is selected.

By default, this check box is selected.

Elements Analysis colors

Activate elements' analysis colors: Click Configure... button to define in Element's Analysis dialog box how to display dimensions using different colors according to their types (true dimensions, invalid dimensions, etc.).
By default, this check box is selected.

Sectioning Properties

Background color

Defines the background color of the section.

From face: Defines background color of the section from the face.
A same color as that of the face is applied to the section.

Custom: Lets you manually define the background color of the section.

By default, Custom is selected.

Pattern

Defines the pattern for the section.

None: No pattern is applied to the section.

Material: Defines the pattern from the material used.

By default, None is selected.

Apply only to active product: Applies material only to the elements, which are under the active product.
By default, this check box is cleared.

Annotation Parameters

Display parameters under annotation feature node

Defines that knowledge parameters (such as tolerance values, datum label, etc.) of annotations should be displayed under the annotation feature node in the tree; also defines that feature parameters of dimensions (accessible through the Edit Generative Parameter command) should be displayed under the dimension feature node in the tree.

Note that to have the value of the parameters displayed in the tree, you need to select the With value knowledge setting.

By default, this check box is cleared.

Surface Normal

Display for shifted profile tolerance: Defines whether the normal of all the selected surfaces are displayed, or not, when a shifted profile tolerance is specified or queried.
By default, this check box is cleared.

3D Annotation Query

Allow query for default annotation (automatic selection mode): Defines whether the highlight for geometric element involved in default annotation is allowed with 3DMaster query .
By default, this check box is selected.

Capture display

Mirror annotations: Defines whether annotations are automatically mirrored when displaying a capture.
By default, this check box is selected.