Working with Multi-Sections Surfaces

You can create a multi-sections surface by sweeping one or more section curves along an automatically computed or user-defined spine. The surface can be made to respect one or more guide curves.

This task shows you how to:

Before you begin: Create a 3D shape containing several curves.
See Also
In the Knowledge Base
When smoothing the multisections surface, why does the spine plane exceed the tolerance limits?

Create a Multi-Sections Surface

You can create a multisections surface by sweeping one or more section curves along the spine.

  1. From the Surface section of the action bar, click Multi-sections Surface .
  2. Select one or more planar section curves.
    Important:
    • The curves must be continuous in point.
    • You need to have GS1 installed to create a multisections surface with more than two sections.
    Tip: A closing point can be selected for the closed section curves.
  3. Optional: Select a support surface for each of the extremity section curve.

    Note: The boundary must fully lie on the support. The support surfaces must not be parallel to the sections.

  4. Optional: In the Continuity list, select the continuity type for each support surface.

    By default, the continuity is set to Tangent.

    Note: You can modify the continuity type either from:
    • the dialog box: select the input in the list and modify the type from the Continuity list, or
    • the work area: click the widget to switch from one type to another or right-click it and select the type. Widgets are useful to visualize whether and which continuity is set on a section curve.


      		indicates tangent continuity.


      		indicates curvature continuity.

  5. Click Preview.
    Multisections surface defined by three planar

    Important: The sections can be 3D curves provided that the intersection between one 3D profile and all guides is coplanar (if three guides or more are defined.)
  6. Optional: Select one or more guide curves.
    Important: The guide curves must intersect each section curve and must be continuous in point.
    The first guide curve is a boundary of the multisections surface if it intersects the first extremity of each section curve.

    Similarly, the last guide curve is a boundary of the multisections surface if it intersects the last extremity of each section curve.

    Multisections surface defined by two planar and two guide curves

    You can make a multisections surface tangent to an adjacent surface by selecting an end section that lies on the adjacent surface. In this case, the guides must also be tangent to the surface.

    Multisections surface tangent to the existing surface



    You can also impose tangency conditions by specifying a direction for the tangent vector (selecting a plane to take its normal, for example). This is useful for creating 3D shape representations that are symmetrical with respect to a plane. Tangency conditions can be imposed on the two symmetrical halves.

    Similarly, you can impose a tangency onto each guide, by selection of a surface or a plane (the direction is tangent to the plane's normal.) In this case, the sections must also be tangent to the surface.

    Note: You can create a multisections surface by sweeping a section curve along two guide curves intersecting each other at one extremity.
  7. Optional: Select the support for extremity guide curves and select the continuity type for each support surface.
    By default, the continuity is set to Tangent.
  8. Click OK.
    The surface (identified as Multi-sections Surface.xxx) is added to the tree.

    In case a section is defined by a closed curve, the extremum points are aggregated under the parent command that created them and put in no show in the tree.

Define Smooth Parameters

You can define the smoothing parameters on the multisection surfaces.

In the Smooth parameters area, you can select the following options:
OptionDescription
Angular Correction Smoothes the lofting motion along the reference guide curves. This may be required when small discontinuities are detected for the spine tangency or the reference guide curves' normal. The smoothing is done for any discontinuity, for which angular deviation is smaller than the input value, and therefore helps generating better quality for the resulting multisections surface. Over 0.01deg, the smoothing is canceled. By default, the angular correction is set to 0.5deg.
Angular Correction Smoothes the lofting motion by deviating from the guide curves. A smoothing is performed using correction default parameters in tangency and curvature. By default, the deviation is set to 0.001mm, as defined in the preferences.

Select a Spine

You can select a spine to guide the multisections surfaces.

In the Spine box, select Computed Spine to use a spine that is automatically computed or select a curve to impose that curve as the spine.
  • The spine curve should be normal to each section plane and must be continuous in tangency. Otherwise, it may lead to an unpredictable shape.
  • If the plane normal to the spine intersects one of the guiding curves at different points, it is advised to use the closest point to the spine point for coupling.
  • You can create multisections surfaces between closed section curves. These curves have point continuity at their closing point. This closing point is either a vertex or an extremum points automatically detected and highlighted by the system. By default, the closing points of each section are linked to each other. The red arrows in the figures below represent the closing points of the closed section curves. You can change the closing point by selecting any point on the curve.
    The surface is twisted

    A new closing point has been imposed to get a nontwisted surface

Relimit the Multisections Surface

You can specify the relimitation type.

Select either to limit the multisections surface on the start section (Relimited on start section), only on the end section (Relimited on end section), on both, or on none.
  • When none of the options are selected: the swept surface is extrapolated up to the spine limits.
  • When both options are selected: the multisectionssections surface is limited to corresponding .
  • When one or both options are cleared: the multisections surface is swept along the spine:
    • If the spine is a user spine, the multisections surface is limited by the spine extremities or by the first guide extremity met along the spine.
    • If the spine is an automatically computed spine, and no guide is selected: the multisections surface is limited by the start and end sections.
    • If the spine is an automatically computed spine, and one or two guides are selected: the multisections surface is limited by the guides extremities.
    • if the spine is an automatically computed spine, and more than two guides are selected: the spine stops at a point corresponding to the barycenter of the guide extremities. In any case, the tangent to the spine extremity is the mean tangent to the guide extremities.

Both options-selected

End section option cleared

Important: After the multisections surface is relimited, the following constraint needs to be fulfilled:
  • the plane normal to the guides spine defined at the points relimitation point must intersect the
  • the resulting from this intersection must belong to the section.

Use a Canonical Element

You can detect planar surfaces to be used as planes for features needing one in their definition.

Select the Canonical portion detection to automatically detect planar surfaces to be used as planes for features needing one in their definition.
Initial multisections surface with planar faces

Using a planar face as reference for a sketch

Resulting sketch

Use an Area Law

You can define and control the shape of a multisectionssections surface between its .

Important: The Area law option is available only if you have the Generative Shape Morphing (GSO) and Cast & Forged Part Design (CFO) licenses.

To create a multisections surface allowing an area law, the following inputs can be used:

  • planar sections (with no tangency conditions)
  • a spine (optional)
  • a guide curve (either no guide curve, one or two guide curves)

Lets you define the law that is used to create the multisections surface.

In our example, three sketches with closed contours have been created and filled. A spine between these sections has been created:



  1. Click Measure to compute the geodesic length of the spine:



  2. Click Split to split the spine by the section plane.
  3. Click Measure again to compute the geodesic length of the resulting curve:



  4. Using the Sketcher, create a line and a curve corresponding to the previous computed lengths.
    Important: Radius values (16.2, 9.5 and 14.142) are similar to the radius values of the corresponding sections (that is R=√(A/π) where A is the section area).
  5. Click Extract to create separate elements of the line and curve.
  6. Click Law to create the law from the previously extracted elements.
  7. Select the Reference line and the Definition curve.
  8. Click OK to create the law.
  9. Click Multi-sections Surface .
    The Multi-sections Surface Definition dialog box appears.
  10. Select the sketches as the planar section curves.
  11. Select the Area law tab.
  12. In the Law box, specify the length law to be used to control the section area.

    Here, select the law we have newly created.

    The Intermediate sections deviation option only applies to intermediate sections (unlike the Deviation option that applies to the sections extremities) and is homogeneous with the selected law. It specifies the deviation of the length law to be applied to the intermediate sections in smooth the resulting shape.

  13. Click OK to create the multisections surface.
    Important: You can select the Display computed area law check box to display in the 3D geometry:
    • You need to first start the computation of law before displaying its computed area in the 3D geometry. Double-click the law in the tree and then click Preview to display the computed area.
    • Red indicates the area law.
    • Blue indicates the sections areas and a flag on each section that displays the deviation between the area law and the sections areas as well as the equivalent radius of each section.



Creating a Coupling

There are three kinds of coupling during the creation of the multisections surface. These couplings compute the distribution of isoparameters on the surface.

Coupling between two consecutive sections

This coupling is based on the curvilinear abscissa.

  1. Click Multi-sections Surface .
  2. Select the two consecutive sections.


  3. Click OK.


    If you want to create a coupling between particular potots, you can add guides or define the coupling type.



Coupling between guides

The coupling of the sections is performed by the spine.

If a guide is the concatenation of several curves, the resulting multisections surface contains as many surfaces as curves within the guide.



Before you begin: Several coupling types are available, depending on the section configuration:
  • Ratio: the curves are coupled according to the curvilinear abscissa ratio.
  • Tangency: the curves are coupled according to their tangency discontinuity points. If they do not have the same number of points, they cannot be coupled using this option.
  • Tangency then curvature: the curves are coupled according to their tangency continuity first then curvature discontinuity points. If they do not have the same number of points, they cannot be coupled using this option.
  • Vertices: the curves are coupled according to their vertices. If they do not have the same number of vertices, they cannot be coupled using this option.

Manual Coupling

If the number of vertices differ from one section to another, you need to perform a manual coupling.

  1. Select the sections for the multisectionssections surface, and confirm their orientations.
  2. In the Coupling tab, select Tangency and click Preview.
    An error message is displayed as the number of discontinuity points on the first section is greater than on the other two .

    The points that could not be coupled, are displayed in the geometry with the specific symbol depending on the selected mode, along with coupling lines:



    • In Tangency mode: uncoupled tangency discontinuity points are represented by a square.

    • In Tangency then curvature mode:
      • Uncoupled tangency discontinuity points are represented by a square.
      • Uncoupled curvatures discontinuity points are represented by an empty circle.
    • In Vertices mode: uncoupled vertices are represented by a full circle

  3. Double-click in the coupling list, or select Add in the context menu, or using the Add option, and manually select a point on the first section.
    The Coupling dialog box appears.
  4. Select a corresponding coupling point on each section of the multisections surface.
    The Coupling dialog box is updated consequently, and the coupling curve is previewed, provided Display coupling curves check box is selected.

    When a coupling point has been defined on each section, this dialog box automatically disappears.



  5. Click OK.
    The multisections surface is created as defined with the coupling specifications.

    The same multisections- surface without coupling and with Ratio option would have looked like this:



    Note the increased number of generated surfaces.

Tips:
  • You can create a coupling point on the fly, using the Create coupling point context menu item (click in the work area to display the context menu) instead of selecting an existing point.
  • To edit the coupling, double-click the coupling name in the list (Coupling tab) to display the Coupling dialog box. Then you select the point to be edited from the list and create/select a replacing coupling point, then click OK.
  • Use the context menu on the coupling list to edit defined couplings.

Edit a Multisections Surface

You can edit the multiselection surfaces.

Double-click the multisections surface either in the work area or in the tree. More possibilities are available with the context menu:

  • right-click the surface to access the following options:

    • Add Section
    • Computed Spine
    • Add Spine
    • Add Guide
    • Add Guide
    • Add Coupling
    • Ratio Coupling
    • Tangency Coupling
    • Tangency then Curvature Coupling
    • Vertices Coupling
    • No relimitation

  • right-click the multisections surface reference elements, either a curve in the dialog box list or the red text on the figure to access the following options:

    • Replace
    • Remove
    • Replace Support
    • Remove Support
    • Computed Tangent
    • Create Closing Point
    • Replace Closing Point
    • Remove Closing Point
    • Add
    • Add After
    • Add Before
    Here is the result when the tangency condition is removed between the blue multisections surface and the adjacent surface