Using the Advance View of the Synchronization Report

You can use the advance view of the synchronization report to have an extensive view of the outcome of the synchronization process. You can apply filters and also manage the display of the columns of the advance report.

This task shows you how to:

Before you begin: Map and simulate a synchronization to display the synchronization report .
See Also
Synchronization Analysis

Display Advance Report

The advance view displays the synchronization results in a table to provide detailed view of each object. You can use cross highlight behaviour, apply filters, and reframe on the required elements from the report.

  1. In the Simulation tab of the synchronize panel, under Report, expand the Advance Report.
    A table listing the content impacted by the synchronization appears.
    Note: Based on the selection in the pie chart view, the information in the table is filtered.

    The results are displayed in the columns based on the synchronized elements:

    • Electrical Geometry: Provides the name of the electrical geometry containing the object
    • Element: Provides the name of the object
    • Action: Provides the type of action performed on the object during the process
    • Status: Provides the synchronization status of the object
    • Flatten Status: Provides the flatten status of a branch
    • Length: Provides the length of the element for branches and segments after the synchronization process
    • Impacted Table: Provides the information about tables impacted due to newly added, deleted, or modified elements from any table created using Table Management
    • Length before: For branches and segments, provides the length of the element before the synchronization process
    • Length: For branches and segments, provides the length of the element after the synchronization process
    • Message: When errors or warnings occur during the synchronization, the following messages can appear:
      • "The 3D harness flattening and 3D harness design link is broken"
      • "Error during the analyze"
      • "Error during the Remove Component Synchronization"
      • "Error during the Segment Structure Synchronization"
      • "Error during the Add Component Synchronization"
      • "Error during the attribute access"
      • "Error during the Replace Component Synchronization"
      • "Error during the Segment Attribute Synchronization - Different Segment Structure"
      • "Error during Attribute Synchronization - Internal link failed to 3D harness flattening from 3D harness design"
      • "Error during the Segment Attribute Synchronization - Different Number of Supports"
      • "Error during the Segment Attribute Synchronization - Different Supports Configuration"
      • "Error during the Add Component - The original component document is not saved"
      • "Error during the Wire Route Synchronization"
      • "Error during the Protective Covering Synchronization - Underlying Curves are not connected"
      • "Error during the Protective Covering Synchronization - Underlying Curves are not tangential"
      • "Error during the Device Move"
      • "Error during Segment Move"

  2. Modify the display of the report by hiding or showing the required columns and sorting them in required order. To do so:
    1. Right-click the required column header in the table and select Hide Column or Show Column.

      You can select Show all columns to display all the columns.

    2. Click a column header.
      The arrow appears in the column header. The results are sorted in ascending alphabetical order.
    3. Click the column header again.
      The arrow appears in the column header. The results are sorted in descending alphabetical order.
  3. Click Generate Report .
    A .csv file is generated. It displays the electrical geometry, element, status, and message information.
    Important: If you have applied filters, only the filtered view is exported in .csv format.

Filter the Advance Report

You can filter the synchronization results in the report and in the 3D area.

  1. Hover over the filter icon in a column header.
  2. Click .
    The synchronized content is listed. By default, all the values are selected.
  3. Optional: Enter the required string to filter the synchronized content.

    To clear or select all the values, select the check box prefixing the box.

  4. Click in the 3D area outside the table.
    The filter is applied and the filter icon turns to .
  5. To remove the filter, click and then Reset all.