*DRUCKER PRAGER

Specify the extended Drucker-Prager plasticity model.

This option is used to define yield surface and flow potential parameters for elastic-plastic materials that use one of the extended Drucker-Prager plasticity models. It must be used in conjunction with the DRUCKER PRAGER HARDENING option and, if creep material behavior is included in an Abaqus/Standard analysis, with the DRUCKER PRAGER CREEP option.

This page discusses:

See Also
*DRUCKER PRAGER HARDENING
*DRUCKER PRAGER CREEP
In Other Guides
Extended Drucker-Prager Models

ProductsAbaqus/StandardAbaqus/Explicit

TypeModel data

LevelModel

Optional parameters

DEPENDENCIES

Set this parameter equal to the number of field variable dependencies included in the definition of the material parameters other than temperature. If this parameter is omitted, it is assumed that the material parameters depend only on temperature. See Material Data Definition for more information.

ECCENTRICITY

This parameter is only for use with SHEAR CRITERION=HYPERBOLIC or SHEAR CRITERION=EXPONENT FORM or if creep material properties are included with SHEAR CRITERION=LINEAR.

It is used to define the flow potential eccentricity, ϵ. The eccentricity is a small positive number that defines the rate at which the hyperbolic flow potential approaches its asymptote. The default is ϵ=0.1 for the exponent model; and if ψ=β, it is set to ϵ=(d|0-pt|0tanβ)/(σ¯|0tanβ) for the hyperbolic model to ensure associated flow (the terms are defined in Extended Drucker-Prager Models).

SHEAR CRITERION

Set SHEAR CRITERION=LINEAR (default) to define the linear yield criterion. This is required if creep material behavior is included for an Abaqus/Standard analysis.

Set SHEAR CRITERION=HYPERBOLIC to define the hyperbolic yield criterion.

Set SHEAR CRITERION=EXPONENT FORM to define the exponent form as a yield criterion.

TEST DATA

This parameter is only for use with SHEAR CRITERION=EXPONENT FORM.

Include this parameter if the material constants for the exponent model are to be computed by Abaqus from triaxial test data at different levels of confining pressure. The TRIAXIAL TEST DATA option must be used for this purpose.

Data lines to define a linear Drucker-Prager plasticity model (SHEAR CRITERION=LINEAR)

First line
  1. Material angle of friction, β, in the pt plane. Give the value in degrees.

  2. K, the ratio of the flow stress in triaxial tension to the flow stress in triaxial compression. 0.778K1.0. If this field is left blank or a value of 0.0 is entered, the default of 1.0 is used. If creep material behavior is included, K should be set to 1.0.

  3. Dilation angle, ψ, in the pt plane. Give the value in degrees.

  4. Temperature.

  5. First field variable.

  6. Second field variable.

  7. Etc., up to four field variables.

Subsequent lines (only needed if the DEPENDENCIES parameter has a value greater than four)
  1. Fifth field variable.

  2. Etc., up to eight field variables per line.

Repeat this set of data lines as often as necessary to define the dependence of the material parameters on temperature and other predefined field variables.

Data lines to define a hyperbolic Drucker-Prager plasticity model (SHEAR CRITERION=HYPERBOLIC)

First line
  1. Material angle of friction, β, at high confining pressure in the pq plane. Give the value in degrees.

  2. Initial hydrostatic tension strength, pt|0. (Units of FL−2.)

  3. Not used.

  4. Dilation angle, ψ, at high confining pressure in the pq plane. Give the value in degrees.

  5. Temperature.

  6. First field variable.

  7. Second field variable.

  8. Third field variable.

Subsequent lines (only needed if the DEPENDENCIES parameter has a value greater than three)
  1. Fourth field variable.

  2. Etc., up to eight field variables per line.

Repeat this set of data lines as often as necessary to define the dependence of the material parameters on temperature and other predefined field variables.

Data lines to define a Drucker-Prager plasticity model with the exponent law (SHEAR CRITERION=EXPONENT FORM) and without test data (TEST DATA)

First line
  1. Material constant a.

  2. Exponent b. To ensure a convex yield surface, b1.

  3. Not used.

  4. Dilation angle, ψ, at high confining pressure in the pq plane. Give the value in degrees.

  5. Temperature.

  6. First field variable.

  7. Second field variable.

  8. Third field variable.

Subsequent lines (only needed if the DEPENDENCIES parameter has a value greater than three)
  1. Fourth field variable.

  2. Etc., up to eight field variables per line.

Repeat this set of data lines as often as necessary to define the dependence of the material parameters on temperature and other predefined field variables.

Data lines to define a Drucker-Prager plasticity model with the exponent law (SHEAR CRITERION=EXPONENT FORM) and with test data (TEST DATA)

First line
  1. Not used.

  2. Not used.

  3. Not used.

  4. Dilation angle, ψ, at high confining pressure in the pq plane. Give the value in degrees.

  5. Temperature.

  6. First field variable.

  7. Second field variable.

  8. Third field variable.

Subsequent lines (only needed if the DEPENDENCIES parameter has a value greater than three)
  1. Fourth field variable.

  2. Etc., up to eight field variables per line.

Repeat this set of data lines as often as necessary to define the dependence of the material parameters on temperature and other predefined field variables.