Common Difficulties Associated with Contact Modeling in Abaqus/Standard

When modeling the contact between two faceted surfaces, it is often possible for small gaps or penetrations to occur at individual nodes. This problem is particularly common when the two surfaces have dissimilar meshes. Abaqus/Standard uses two default methods for dealing with initial penetrations:

• In general contact small initial overclosures are automatically adjusted to remove the penetrations.

• In contact pairs initial overclosures are interpreted as interference fits and resolved accordingly (see Resolving Large Interference Fits below).

You can improve the accuracy of a contact simulation by having Abaqus/Standard adjust the position of the secondary surface to ensure that all secondary nodes that should initially be in contact with the main surface start out in contact without any penetration (see Contact Initialization for General Contact in Abaqus/Standard and Contact Initialization for Contact Pairs in Abaqus/Standard). When an intended initial clearance or overclosure is small compared to typical dimensions of the bodies in contact and a small-sliding contact pair is used, you can specify the clearance or overclosure precisely (see Additional Contact Initialization Options for Small-Sliding Contact in Abaqus/Standard).

The small-sliding contact tracking approach is more sensitive than the finite-sliding tracking approach to initial local gaps at the contact interface. In small-sliding contact each secondary node interacts with a contact plane defined from the finite element approximation of the main surface, as discussed in Contact Formulations in Abaqus/Standard. Abaqus/Standard can define these planes only when each secondary node can be projected onto the main surface. Having these secondary nodes start the simulation contacting the main surface allows Abaqus/Standard to form the most accurate contact planes for the secondary nodes.

The contact initialization algorithm may occasionally infer large initial overclosures where you do not intend initial overclosures to exist. For example, specifying incorrect surface normals can cause the contact initialization algorithm to interpret a physical gap as a penetration, as discussed in Orientation Considerations for Shell-Like Surfaces. Minor changes to the surface or contact definition will typically avoid undesired overclosures, but these situations typically call for some diagnosis to determine how to avoid the problem.

Overclosures on Discontinuous Surfaces

Figure 1 shows an example with a large, unintended initial overclosure. In this case a single contact pair with discontinuous surfaces is meant to enforce contact in two distinct regions (Table 1Orientation Considerations for Shell-Like Surfaces shows which contact formulations allow discontinuous surfaces). The arrows in Figure 1 show the positive normal direction for each surface region. The surface-to-surface contact formulation searches along the secondary-surface normal direction (in the positive and negative directions) for potential interaction points on the main surface. The search emanating from point A identifies point B as the only potential interaction point for point A in this example. The contact pair interprets this as a valid penetration because no better candidate interaction location is found and surface normals are opposed at points A and B. Methods to avoid this unintended overclosure include:

• defining separate contact pairs with continuous surfaces for each of the two distinct contact regions; and

• specifying general contact, which filters out nearly all unintended initial overclosures.

Figure 1. Example of an unintended initial overclosure due to a modeling error involving discontinuous surfaces.

As previously discussed, Abaqus/Standard optionally interprets initial overclosures as interference fits. You should use one of the methods discussed above to remove any initial overclosures that are an unintended result of mesh discretization or errors in defining contact surfaces. In some cases the interference fit may be intended but may be too large to be resolved robustly with the method that is used by default for contact pairs in Abaqus/Standard (which is to resolve overclosures in a single increment). In this situation you should modify the contact model to allow resolution of overclosures over multiple increments (see Modeling Contact Interference Fits in Abaqus/Standard for more information). If you choose to have initial overclosures treated as interference fits for general contact, they are automatically resolved over multiple increments (see Contact Initialization for General Contact in Abaqus/Standard).

Rigid body motion is generally not a problem in dynamic analysis. In static problems rigid body motion occurs when a body is not sufficiently restrained. “Numerical singularity” warning messages and very large displacements indicate unconstrained motion in a static analysis. Therefore, if contact is used to constrain rigid body motion in static problems, ensure that the appropriate surface pairs are initially in contact (see Contact Initialization for General Contact in Abaqus/Standard and Contact Initialization for Contact Pairs in Abaqus/Standard). If necessary, define the model geometry to give a small initial overclosure to the contact pair, or use boundary conditions to move the structures into contact in the first step. The boundary conditions, which are unnecessary in subsequent steps, can be removed after the body is adequately constrained through contact with other components. Similarly, if a rigid body is meant to translate only, constrain its rotational degrees of freedom.

Frictional sticking can constrain rigid body motion. However, contact pressure must develop before friction can be generated. Therefore, friction is not effective in constraining rigid body motion when surfaces first come into contact. You must temporarily eliminate rigid body motion by defining a boundary condition or by grounding the body with soft springs or dashpots.

If you are unable to prevent rigid body motion through modeling techniques, Abaqus/Standard offers some tools to automatically stabilize rigid bodies in contact simulations. These tools are discussed in Automatic Stabilization of Rigid Body Motions in Contact Problems.

When defining three-dimensional surfaces for use in finite-sliding applications, avoid defining two surface nodes with the same coordinates. Such a definition can give rise to a seam, or crack, in the surface as shown in Figure 2.

Figure 2. Example of doubly defined surface node.

When modeling finite-sliding contact, ensure that the main surface definition extends far enough to account for all expected motions of the contacting parts. Contact along the perimeter of main surfaces should be avoided with the node-to-surface contact formulation.. Abaqus/Standard assumes that the mating secondary surface nodes can fall off the free edge of the main surface, which can cause problems if a secondary node wraps around and approaches its mating main surface from behind. Figure 3 illustrates appropriate and inappropriate main surface definitions.

Figure 3. Example of main surface extension.

A secondary node that falls off a main surface in one iteration may find itself contacting the surface in the very next iteration; this phenomenon is known as chattering. If chattering continues, Abaqus/Standard may not be able to find a solution. This problem is less likely with the surface-to-surface formulation approach, because each contact constraint is based on a region of the secondary surface rather than individual secondary nodes. Request detailed contact printout to the message (.msg) file to monitor the history of a secondary node that might slide off the main surface (see The Abaqus/Standard Message File). The message file output will show the cyclic opening and closing of contact at a secondary node, which will indicate where the main surface needs to be modified.

For node-to-surface contact you can extend the main surface beyond the perimeter of the physical body that it approximates to avoid chattering problems. Chattering can also occur with some contact elements, such as slide line and rigid surface contact elements. Slide line contact elements can also be extended. See Extending Main Surfaces and Slide Lines for details.

Several problems are caused by surfaces created on very coarse meshes. Some of these problems depend on your choice of contact discretization, as discussed later in Discrepancies between Contact Formulations.

Penetrations with Coarsely Meshed Secondary Surfaces

When a coarsely meshed surface is used as a secondary surface for node-to-surface contact, the main surface nodes can grossly penetrate the secondary surface without resistance (see Figure 4). This situation is common when nonmatching meshes come into contact. Refining the secondary surface tends to alleviate this problem.

Figure 4. Main surface penetrations into the secondary surface due to a coarse mesh of the secondary surface for node-to-surface contact.

Surface-to-surface contact will generally resist penetrations of main nodes into a coarse secondary surface; however, this formulation can add significant computational expense if the secondary mesh is significantly coarser than the main mesh (see Contact Formulations in Abaqus/Standard for further discussion).

Contact Occurring at a Single Element

If the mesh on a surface is too coarse, it is possible for a contact interaction to occur entirely within the bounds of a single element. This typically happens when the two contacting surfaces have dissimilar curvature, as depicted in Figure 5.

Figure 5. The main surface contacts the secondary surface at a single element face.

The results from such an interaction are unreliable and generally unrealistic. If the model in Figure 5 uses node-to-surface contact, the main surface penetrates the secondary surface without resistance until it encounters a secondary node, as discussed above. If the main and secondary designations are reversed, the contact constraint is applied at a single secondary node; this concentration creates inaccurately high calculations of the contact pressure. If the model uses surface-to-surface contact, excessive penetration is not likely to occur. However, with only a small number of constraint points involved in the interaction, the averaging algorithm used to enforce surface-to-surface contact performs poorly. Inaccurate contact stress and pressure calculations result.

If contact is occurring at a single element, refine the mesh to spread the interaction across multiple element faces.

Second-order elements not only provide higher accuracy but also capture stress concentrations more effectively and are better for modeling geometric features than first-order elements. Surfaces based on second-order element types work well with the surface-to-surface contact formulation but, in some cases, do not work well with the node-to-surface formulation (see Contact Formulations in Abaqus/Standard for a discussion of these contact formulations).

Some second-order element types are not well-suited for underlying the secondary surface with the combination of a node-to-surface contact formulation and strict enforcement of “hard” contact conditions, because of the distribution of equivalent nodal forces when a pressure acts on the face of the element. As shown in Figure 6, a constant pressure applied to the face of a second-order element without a midface node produces forces at the corner nodes acting in the opposite sense of the pressure.

Figure 6. Equivalent nodal loads produced by a constant pressure on the second-order element face in “hard” contact simulations.

Abaqus/Standard bases important decisions for the node-to-surface contact formulation on contact forces acting on individual secondary nodes; the ambiguous nature of the nodal forces in second-order elements can cause Abaqus/Standard to make a wrong decision. To circumvent this problem, Abaqus/Standard automatically converts most three-dimensional second-order elements with no midface node (i.e., serendipity elements) that form a secondary surface into elements with a midface node. For the three-dimensional 18-node gasket elements, the midface nodes are also generated automatically if they are not given in the element connectivity. The presence of the midface node results in a distribution of nodal forces that is not ambiguous for the contact algorithm.

The element families C3D20(RH), C3D15(H), S8R5, and M3D8 are converted to the families C3D27(RH), C3D15V(H), S9R5, and M3D9, respectively. Since Abaqus/Standard does not convert second-order coupled temperature-displacement, coupled thermal-electrical-structural, and coupled pore pressure–displacement elements, you should specify a penalty or augmented Lagrange constraint enforcement method to approximate hard pressure-overclosure behavior (see Contact Constraint Enforcement Methods in Abaqus/Standard). Abaqus/Standard will interpolate nodal quantities, such as temperature and field variables, at the automatically generated midface nodes when values are prescribed at any of the user-defined nodes. Abaqus/Standard does not convert second-order serendipity elements if the secondary surface is used in a tied contact pair.

Second-order tetrahedral elements (C3D10 and C3D10HS) have zero contact force at their corner nodes. This combination of second-order triangular secondary facets, a node-to-surface contact formulation, and strict enforcement of “hard” contact conditions is disallowed to avoid a high likelihood of convergence problems and poor predictions of contact pressures that would occur with this combination. To avoid this combination, use at least one of the following alternatives:

• Use the surface-to-surface contact formulation (generally recommended) instead of the node-to-surface contact formulation;

• Use the penalty constraint enforcement method (generally recommended) or augmented Lagrange constraint enforcement method instead of strict enforcement of “hard” contact conditions; or

• Use modified 10-node tetrahedral elements (C3D10M) instead of second-order tetrahedral elements.

By default, Abaqus/Standard continues to iterate until the severe discontinuities associated with changes in contact status are sufficiently small (or no severe discontinuities occur) and the equilibrium (flux) tolerances are satisfied. Alternatively, you can choose a different approach in which Abaqus/Standard continues to iterate until no severe discontinuities occur. These two approaches are discussed in more detail in Severe Discontinuities in Abaqus/Standard. The default treatment of severe discontinuity iterations reduces the likelihood of excessive iterations associated with chattering between contact states when the contact conditions are weakly determined. An example of a region with weakly determined contact conditions is near the center of a flat punch that contacts a thin plate supported at its edges.

For most types of contact, if during an iteration the penetration calculated for any contact pair exceeds a specific distance ($h_{crit}$), Abaqus/Standard abandons the increment and tries again with a smaller increment size. There is no critical penetration distance for finite-sliding, surface-to-surface contact (including general contact) and for small-sliding contact in geometrically linear analyses.

The default value of $h_{crit}$ is the radius of a sphere that circumscribes a characteristic surface element face. When calculating the default value, Abaqus/Standard uses only the secondary surface of the contact pair. The value of $h_{crit}$ for each contact pair in the model is printed in the data (.dat) file. While the default value of $h_{crit}$ should prove to be sufficient for the majority of contact simulations, in some cases it may be necessary to change the default value for a given contact pair. These cases include:

• Models in which the main surface is highly curved. The default value of $h_{crit}$ may sometimes lead to situations as shown in Figure 7. During the iterative solution process a secondary node initially at point a may move to point b, penetrating the main surface with overclosure h less than $h_{crit}$ . Abaqus/Standard may attempt to move the secondary node to point c on the main surface. To avoid this situation, specify a smaller value for $h_{crit}$ to force Abaqus/Standard to abandon the increment and to try a smaller increment size.

  Figure 7. Effect of the critical penetration distance on a highly curved main surface.
  
  

• Models in which Abaqus/Standard cannot calculate a reasonable $h_{crit}$ because a node-based surface is used. If there are other contact pairs in the model with surfaces, Abaqus/Standard uses the average dimension of all of the secondary surface element faces. If there are no other contact pairs, Abaqus/Standard uses a characteristic element dimension of the entire model.

• Models in which the contact face dimensions in a secondary surface vary greatly.

• Models in which the secondary surface mesh is very refined compared with the typical surface dimensions so that overclosures much larger than the default $h_{crit}$ can be resolved easily.

• Models in which contact pairs with softened contact allow significant penetration (see Contact Pressure-Overclosure Relationships).

CONTACT PAIR, HCRIT=$h_{crit}$

Nonuniform contact pressure distributions are likely to occur when very different mesh densities are used on the two deformable surfaces making up a contact interaction. The nonuniformity can be particularly pronounced when “hard” contact is modeled and both surfaces are modeled with second-order elements, including modified, second-order tetrahedral elements. In such cases oscillations and “spikes” in the contact pressure may occur. Smoother contact pressures may be obtained for surfaces modeled with second-order elements by using penalty-type contact constraint enforcement (see Contact Constraint Enforcement Methods in Abaqus/Standard).

For second-order axisymmetric elements the contact area is zero at a node lying on the symmetry axis $\left(r=0\right)$. To avoid numerical singularity problems caused by a zero contact area, Abaqus/Standard calculates the contact area as if the node were a small distance from the symmetry axis. This may result in inaccurate local contact stresses calculated for nodes located on the symmetry axis.

Contact of a surface with itself (self-contact) is provided for cases in which the original geometry is very different from the (deformed) geometry at which contact takes place. It would then be difficult for you to predict which parts of the surface will come into contact with each other. Where possible, it is always computationally more economical to declare parts of the surface as main and parts as secondary. The same unpredictability makes it impossible to determine a priori which side will be the main and which side the secondary. Therefore, Abaqus/Standard uses a symmetric contact model: every single node of the surface can be a secondary node and can simultaneously belong to main segments with respect to all other nodes.

Because each surface is acting as both a secondary and a main, the results of symmetric contact analyses can be confusing and inconsistent. These difficulties are discussed more fully in Using Symmetric Main-Secondary Contact Pairs to Improve Contact Modeling.

The term overconstraint refers to a situation in which multiple kinematic constraints outnumber the degrees of freedom on which they act. Overconstraints often lead to inaccurate solutions or failure to obtain a converged solution. Contact conditions strictly enforced with the direct constraint enforcement method (using Lagrange multipliers) are sometimes involved in overconstraints. See Overconstraint Checks for a detailed discussion and examples of overconstraints and how Abaqus/Standard will treat overconstraints based on the following classifications:

• Overconstraints detected in the model preprocessor

• Overconstraints detected and resolved during analysis

• Overconstraints detected in the equation solver

Abaqus/Standard will automatically resolve many types of overconstraints; however, many overconstraints involving contact cannot be resolved and will be exposed to the equation solver. The equation solver will often issue “zero pivot” or “numerical singularity” warning messages as a result of overconstraints; when this occurs, Abaqus/Standard will provide a warning message with information that is helpful for determining what contributed to the overconstraint so that you can resolve it. Occasionally overconstraints do not create warning messages; this does not necessarily mean that the overconstraints have not adversely affected the analysis.

The most observable difference between node-to-surface and surface-to-surface discretization is the amount of penetration that occurs between surfaces. This is because node-to-surface discretization computes penetrations only at secondary nodes, while surface-to-surface discretization computes penetrations in an average sense over a finite region. For example, when a secondary surface slides across a convex portion of a main surface, the secondary surface will tend to ride a bit higher with surface-to-surface discretization than with node-to-surface discretization, as shown in Figure 8 (the opposite is true at a concave portion of a main surface). Figure 9 shows another case in which the two contact discretizations behave fundamentally differently due to the different approaches to computing penetrations. Both discretizations converge to the same behavior as the mesh is refined.

Figure 8. Comparison of contact discretizations in an example with convex curvature in the main surface (forming application).

The differences in computed penetrations can sometimes fundamentally affect the results of an analysis. Be aware of this possibility when converting models from one contact formulation to another. Various aspects of preexisting models, such as the friction coefficient or the pressure-overclosure relationship, may have been inadvertently tuned to the behavior that occurs with a particular contact formulation.

Figure 9. Comparison of contact discretizations in an example with a relatively flexible secondary surface wrapping around a corner of a main surface.

Figure 10 shows an example in which a circular rigid body is pushed into a deformable body.

Figure 10. Example with two bodies initially touching at a single point.

In the initial configuration shown, the two bodies touch at a single point, which corresponds to a secondary node location. The following scenarios are likely for respective analyses of this model with node-to-surface and surface-to-surface discretization:

• With node-to-surface discretization, the first iteration is performed with one active contact constraint. A converged solution is obtained with a reasonable number of iterations and increments.

• With surface-to-surface discretization, penetrations are computed in an average sense over finite regions of the surface, so a positive gap distance is computed for all potential contact constraints even though the surfaces touch at one of the secondary nodes. However, the finite-sliding, surface-to-surface contact formulation detects that the surfaces are initially touching and by default automatically activates localized contact damping in the neighborhood where the gap distance is zero. Without such damping, Abaqus/Standard may not obtain a converged solution due to an unconstrained rigid body mode. This contact damping typically has an insignificant effect on the converged solution, and the damping is completely removed by the end of the step.

If you deactivate the automatic localized damping for the finite-sliding, surface-to-surface formulation—or if you are using the small-sliding, surface-to-surface formulation—you should use one of the techniques discussed above in Difficulties Resolving Initial Contact Conditions to remove the perceived initial gap between surfaces and prevent rigid body modes in the analysis.

CONTACT PAIR, MINIMUM DISTANCE=NO

CONTACT INITIALIZATION DATA, MINIMUM DISTANCE=NO

Node-to-surface discretization uses a contact normal direction based on the main surface normal, whereas surface-to-surface discretization uses a contact normal direction based on the secondary surface normal (averaged over a region nearby the secondary node). For most active contact definitions the secondary and main surfaces are nearly parallel, so the main and secondary normals are approximately aligned; in which case this distinction in how the contact normal is determined is not significant. However, in some cases the differences in the contact normal can be significant.

• When modeling large interference fits, surface-to-surface discretization can sometimes cause tangential motion of the secondary surface as the overclosures are resolved. This tangential motion may have undesirable effects on an analysis. See Contact Initialization for General Contact in Abaqus/Standard and Modeling Contact Interference Fits in Abaqus/Standard for more details.

• Contact constraints involving geometric edges of surfaces sometimes use a significantly different contact normal depending on which contact discretization approach is used, because the normals for the secondary and main surfaces may not directly oppose each other.

• The contact opening distance output variable (COPEN) can vary considerably depending on what type of contact formulation is used if the contact surfaces are not parallel. For node-to-surface discretization, the opening distance that is reported approximates the closest distance to the main surface; for surface-to-surface discretization, the opening distance that is reported corresponds to the distance from the secondary surface to the main surface along the secondary normal direction. The opening distance for surface-to-surface discretization is undefined if a line emanating from the secondary surface in the secondary normal direction does not intersect the main surface (as discussed in Using the Small-Sliding Tracking Approach, if a small-sliding constraint cannot be formed in such a case for the small-sliding, surface-to-surface formulation, Abaqus/Standard automatically reverts to the node-to-surface approach for individual constraints).

The finite-sliding, surface-to-surface formulation is often better-suited than other contact formulations for modeling contact near corners. In the example shown in Figure 11, the secondary surface is on the “outer” body (that is, the body with a reentrant corner). With node-to-surface discretization a single constraint acts at the corner secondary node in the “average” normal direction of the main surface, which often leads to poor resolution of contact, non-physical response, and even early termination of an analysis. However, surface-to-surface discretization generates two constraints near the corner for the respective faces, as shown in Figure 11, resulting in more stable contact behavior.

Figure 11. Comparison of contact formulations in an example with abutting surfaces having respective interior and exterior corners.